Darcy penetration experimental device

Technical Parameters:

1. Operating environment: temperature 0-40 ° C, relative humidity: ≤90%RH, power supply: 220V/50Hz, which can be continuously operated.

2. Silent and environmentally friendly pump: Saying: 10m, traffic: 12L/min, power: 90W.

3. Shengsha round barrel: inner diameter ф150mm, 500mm high, transparent and thick organic glass, and natural sand.

4. The voltage voltage is 900mm, 150mm width, 100mm long, 100mm wide, 100mm high, and organic glass.

5. Water storage box: The volume is about 60L, PVC material.

6. The fluid used in the experiment-water is full circular design, which fully saves water resources.

7. The frame and countertop are made of 304 st--nless steel. The structure is compact, the appearance is beautiful, and the operation is convenient.

8. Dimensions: 1200 × 500 × 1600mm (long × width × height), the frame is a mobile design, with a foot wheel and imprisoned feet.

9. Building building and smart building electrical installation virtual simulation software

Based on the UNITY3D design, users choose different interactive interface size based on the computer configuration. The software in the software can be rotated, magnified, reduced, and translated at 360 °. There are small assistant tips for software use, the content is as follows:

A. Wet alarm system

1. System summary: Overview of Wet Alarm System

2. Equipment cognition: set up the best perspective, equipment det--ls (display the introduction or parameter of the device), practice (built -in 6 selection questions, there are prompts for correctness and errors), schematic diagrams (can be entered from the schematic diagram Go to the device). The equipment includes: nozzle, water flow indicator, signal butterfly valve, exhaust valve, fire alarm control, executive pressure gauge, high water tank, Weia control cabinet, stabilization tank, flow switch, end -end water testing device, dr--nage facility, water pump combinations, water pump combination Instruments, hydraulic bells, latencys, wet alarms, butterfly valves, stop valves, fire pumps, safe stabilization valves, fire pools.

3. Principles display: Show the working principle of the wet alarm system, the three -dimensional animation demonstration, the three -dimensional model is translucent, and the internal water flow can be seen. Equipped with the exercise module (4 built -in multiple choice questions, there are prompts to choose correctly and errors)

4. Design arrangement: There are choices and calculation questions, each question has scored scores. After submission, the correct answer and score are displayed

1. Product function

Based on the real object of the real pure electric vehicle braking energy recycling system, it can realize the structure and work process of the pure electric vehicle braking energy recycling system.

It is suitable for school teaching needs for pure electric vehicle braking energy recovery systems.

2. Functional characteristics

1. The device fully demonstrates the basic principles of the pure electric vehicle braking energy recovery system. It can dynamically simulate the operating status of pure electric vehicle braking energy recycling systems under different operating conditions.

2. The principle panel adopts high -grade aluminum -plastic plates with 4mm thick corrosion, strike resistance, pollution resistance, fire prevention, and moisture -proof. Principle of schematic diagram; students can intuitively compare the structure of the structure of pure electric vehicle braking energy recycling systems and physical objects to understand and analyze the working principle of the pure electric vehicle braking energy recovery system.

3. Install a little fire switch, operating condition switch, throttle pedal, gear switch, brake switch, motor controller, DC/DC controller, etc., supplemented by the dynamic instructions of the system flowing with the light -emitting diode.

The panel is installed with electric vehicle instruments and current meters to realize data such as current and other data.

4. The panel cabinet part uses a 1.5mm cold plate stamping and forming structure, which is beautiful in appearance; the bottom part is welded with steel structure, the surface is treated with a spraying process, a self -locking wheel device, and a desktop of about 30cm on the base of the teaching plate, which is convenient for convenience Place information, light detection instruments, etc.

5. The equipment uses power battery power supply, and the power battery is installed with a vehicle -carrier charger and charging port. The DC power supply has a short circuit function.

6. Machinery assembly and fitter assembly virtual simulation software: This software is developed based on Unity3D. It can select 6 -level image quality. It has the design and virtual disassembly of the reducer and shaft structure, the design and simulation of common mechanical institutions, institutional resource libraries, institutional resource libraries,, institutional resource library, institutional resource bank, institutional resource library, institutional resource library, institutional resource library, institutional resource bank, institutional resource library, and institutional resource library. Typical mechanical institutions (virtual disassembly of gasoline engines), software is an overall software, which cannot be separate resources.

A. Turbine design and virtual disassembly interface can be selected from turbine sn--l pole cone gear reducer, second -level pilot gear reducer, conical cylindrical gear reducer, coaxial cylindrical gear reducer, cone gear reducer, first -class cylindrical, first -class cylindrical, Gear reducer.

The turbine sn--l tapered gear reducer: automatically play the assembly content after entering the software. Each step in the video has text description

Second -level unfolding cylindrical gear reducer: After entering the software, use the video to play content in the form of video. The video content should include: the name of the parts (scanning the QR code can see the part of the parts), the disassembly presentation (including disassembly, assembly), virtual disassembly Installation (including overall, low -speed shaft, mid -speed axis, high -speed shaft, box cover, box seat)